How to Install Vinyl Tile Backsplash Strips

Please read this entire guide before using the enclosed Sugar Soap sachet or installing your Fantastick Vinyl Tile Backsplash Strip.
IMPORTANT SAFETY WARNING — SUGAR SOAP CLEANER
Harmful if swallowed or misused. Keep the dry sachet and mixed solution out of reach of children and pets. Avoid contact with eyes and mouth. Do not mix with bleach, acids, or other cleaning products. Wash hands thoroughly after handling.
Poisons Information Helpline (South Africa): 0861 555 777 (In a medical emergency, seek urgent medical attention; do not induce vomiting).  

Part 1: Wall Preparation & Testing
1. Before You Begin
  • Check your surface: Your wall must be smooth, dry, sound, clean, and firmly painted (such as smooth plaster, existing ceramic tiles, glass, melamine, or sealed paint). Dust, grease, moisture, rough texture, flaking paint, raw cement, wallpaper, and Teflon/low-energy paints will prevent proper adhesion.  
  • Newly painted walls: Paint must be fully cured, not merely dry to the touch. Allow at least 14 days for water-based paint or 30 days for oil-based paint (or follow your paint manufacturer’s specified curing period) before applying vinyl.  
2. Prepare the Sugar Soap Solution
  • Mix the entire enclosed sachet (approximately 1 teaspoon) into 250 ml of lukewarm water and stir until dissolved in a clearly identified container away from food and drink. (Note: This dilution is specifically for Fantastick’s enclosed sachet, not other sugar soap products.)
  • Spot test first: Test a small, hidden area to ensure the solution does not mark or damage your wall finish.  
3. Clean, Rinse, and Dry
  1. Dampen a soft, clean cloth with the diluted sugar soap solution and wipe the wall gently (do not soak or saturate the surface).
  2. Wipe the same area again using a separate cloth dampened with clean, fresh water to remove any sugar soap residue that could interfere with adhesion.
  3. Let the wall dry completely before testing or installing—never apply vinyl to a damp surface.  
4. Test Your Wall Before Installing
  • Apply the enclosed vinyl tester to a clean, dry, inconspicuous part of the wall, press firmly (including edges), and leave it for at least 24 hours.  
  • If the tester lifts or curls, do not install the full backsplash strip—check for moisture, texture, uncured paint, or cleaning residue, and contact Fantastick if uncertain.  

Part 2: Step-by-Step Centre Hinge Installation
Centre Hinge Method 
What You’ll Need
  • Your Fantastick Vinyl Tile Backsplash Strip
  • Fantastick squeegee (or a felt-edge squeegee / old bank card wrapped in a soft cloth)
  • Masking tape (18–24 mm painter’s tape)
  • Spirit level (or phone level app) and a pencil
  • Scissors or a sharp craft knife
  • Optional: Hair dryer (for sealing edges) 
Step 1: Position & Apply Centre Masking Tape Hinge
  1. Use a spirit level and faint pencil marks to align where your strip will sit (leave at least 5 cm clearance from any direct heat source/stove burner).
  2. Hold the backsplash strip against the wall in its exact position.
  3. Apply a vertical strip of masking tape down the middle from top to bottom (extending onto the wall above and below) to lock your alignment in place.  
Step-by-step Centre Hinge Method installation guide for Fantastick Vinyl Tile Backsplash Strips
Step 2: Peel Backing Paper from the Left Side
  1. Lift the left half of the vinyl strip and fold it back toward the centre masking tape hinge.
  2. Carefully peel the backing paper off that left half right up to the masking tape hinge, and trim or fold the loose backing paper out of the way. (Important: Use the dry method—do not spray water behind the adhesive.)  
Step 3: Squeegee Left Side & Remove Hinge
  1. Lay the left side of the strip onto the wall while holding the outer edge slightly taut so it doesn't touch prematurely.
  2. Using your Fantastick squeegee, smooth the vinyl onto the wall with firm, overlapping strokes working from the centre hinge outward (up and down) toward the left edge to push out all air bubbles.
  3. Once the left half is completely smooth, gently peel off the vertical masking tape hinge.  
Step 4: Peel Right Side & Finish
  1. Lift the right half of the strip, remove the remaining backing paper completely, and squeegee firmly from the centre outward (up and down) toward the right edge.
  2. Final Seal: Re-squeegee all outer edges and corners firmly. (Optional: Use a hair dryer on a gentle warm setting—kept moving—while pressing edges with a soft cloth for an extra-tight seal.)
  3. Erase any faint pencil guide marks cleanly.  

Part 3: Troubleshooting, Care & Removal
  • Small air bubbles: Prick gently with a fine pin and smooth flat with your squeegee.
  • Wrinkles or misalignment: Lift immediately at a low angle, realign carefully, and re-squeegee.
  • Cleaning & Care: Avoid washing or rubbing newly applied edges for the first 24–48 hours. Thereafter, wipe clean with a soft cloth and mild dish soap—avoid abrasive scourers, harsh chemical solvents, and prolonged direct steam.
  • Removal: Warm gently with a hair dryer if needed, lift one corner, and peel back slowly at a low angle. Stop immediately if paint begins lifting. 
Need assistance? Contact Fantastick anytime—we are happy to help!
WhatsApp / Phone: 083 651 5281 | Office: (012) 667 3109 | Website: fantastick.co.za